Wincor Nixdorf BA71-R Bedienungsanleitung

BA71 / BA72LCD TFT 10.4" Flat ScreenLCD TFT 12.1" Flat ScreenUser Manual

Unpacking and checking the Delivery UnitUnpack the parts and check to see whether the delivery matches the infor-mation on the delivery note. The deli

BA71 and BA72 ComponentsScreen ModuleThe screen module represents the main unit of the BA71 / BA72. It compri-ses of a TFT-LCD colour screen, the TFT-

“Stretching” is only possible when a separate TFT conroller is used. So,operating the BA71 / BA72 with the integrated TFT controller at the GXmCPU, “s

TFT Controller for BA71 and BA72Screen Module /TFT ControllerThe TFT-controller used for BA71 / BA72 is identical with the one used forthe SNIkey term

Panel of TFT controllerBoard layout (TFT controller)11250569COM6DSUB socketBA71 / BA72 connectorincl. COM5, LCD interfaceand loudspeakerMDR connectorS

Capacative Touch Screen (Option)GeneralThe TFT Touch Screen works according to the principle of a change inanalog capacitance. It has a glass screen w

The programming interface of the screen is identical to the mouse inter-face. Touch ScreenTouch Screen and Sleep ModeUsing the Touch Screen with a BEE

How to OperateThe Touch Screen responds to the slightest contact, therefore you do nothave to apply much pressure when working with the screen. This n

COM Board for Touch ScreenCOM BoardThe COM Board is an additional board with an ISA bus interface that has2 or 4 COM interfaces (COM5, 6, 7, 8). The C

COM Interface InterruptsCOM5 COM6 COM7 COM7-8 COM6-8 InterruptIRQ9I9---I11IR9IRQ10I10 - - - I12 IR10IRQ11I5 - I4 I8 I13 IR11IRQ12I1---I6IR12IRQ15I3 I2

Herausgegeben von/Published byWincor Nixdorf GmbH & Co. KGD-33094 PaderbornBestell-Nr./Order No.: 0175 00 20397EPrinted in Singapore

Assignment of COM port addresses and interrupts (installation details)Ensure that there is no conflict of hardware port addresses or interrupt re-ques

IRQ12, most likely conflict Mouse Port or PS/2 MouseThese types of mice are supported by Windows NT through theI8042PRT.SYS driver. The mouse usually

The AT COM Board manual numbers the COM ports from 5 to 8. The ori-gin of this numbering is from the BEETLE, which has COM1 to COM4 onthe motherboard.

be impossible by hardware reasons! The problem is, that in such a caseon the AT bus two different hardware instances would be fighting for thesame IRQ

Using shared interrupts for COM ports under Windows 95Under Windows 95, sharing COM ports doesn’t require special provisionsother than correctly speci

Board layout COM boardCOM7COM 5 /COM 6COM81122Interrupt JumperInterrupt RequestI8 I1I9I16IR15IR12IR11IR10IR 9IO 3IO JumperIO 1COM BoardGB - 18

TFT AdapterTFT AdapterIn the case of the BEETLEwith GXmCPU the TFT adapter can be connec-ted with GXm CPU without TFT con-troller and without COM boar

Resistive Touch Screen (Option)Touch ScreenGeneralThe resistive TFT Touch Screen is constructed of a hard-coated polyestertopsheet that is overlaid on

How to OperateTouching the touch screen has the same effect as clicking the left mousebutton. You only need to apply a little pressure with the finger

Touch ScreenGB - 22

BA71 / BA72LCD TFT 10.4" Flat Screen /LCD TFT 12.1" Flat ScreenUser ManualEdition April 2001

Installing and Securing the Screen into PlaceThe screens can be installed either with or without attached operatingelements, as a table top terminal o

Tubular Stand VersionNow fasten the screwon the footed standinto place again usingthe crosstip screw-driver.Ensure that the screwis in the correctposi

Adjustable Screen AngleAdjustable Screen AngleThe BA71 / BA72 is fitted with a joint on the rear. You can optimize theangle of the screen depending on

Ergonomic Terminal WorkplaceErgonomic Terminal WorkplacePlease observe the following when setting up your terminal workplace:Avoid direct glaringand r

InstallationInstalling the Controller in the BEETLE /LFirst ensure that the controller is switched off and the mains supplyplug has been pulled out.Th

In order to be able to install the TFT controller, you must first remove themetal panel that covers the free slots by loosening the screw.Set the jump

Connecting the Speaker CableConnecting the Speaker CableRemove the speaker cable from the BEETLE-CPU by simply unpluggingthe connector. The BEETLE /L

Back of the BEETLE /LConnect the 50-pin data cable of the BA71/BA72 to the TFT controller.Under the small cover on the back of the BA71/BA72 is the so

Connecting the BA71/BA72 to the BEETLE /20The hardware installation is carried out according to the installation of theBA71/BA72 to the BEETLE /L. Whe

Connecting the BA71/BA72 to the PCConnecting the BA71/BA72 to the PCFirst ensure that the controller is switched off and the mains supplyplug has been

Copyright © Wincor Nixdorf GmbH & Co. KG, 2001The reproduction, transmission or use of this document or its contents is not permitted withoutexpre

The Jumper layout of the GXm boardConnecting the BA71/BA72 to the BEETLE/MThe jumper settings of the S1, S2 and S3 slots are decisive for the touchfun

Touch function (COM2 disable))COM2 function (touch disable)After having set the necessary settings on S1, S2 and S3 in the case ofusing the touch func

Connecting the cableThe data cable is to be connected with the 50-pin connector of the TFTadapter. Take care that the thickening of the cable (Ferrit)

Now plug in the cableuntil it snaps in (see il-lustration).When removing thecable press on theconnector release.Installing a TFT adapterNever open the

Inserting the CableInserting the CableThe cable cover is lo-cated in the base plate.Lift the cable cover .Pull the cable coverforward in the direction

Releasing the Cable ConnectionReleasing the Cable ConnectionNever remove a cable from a connector socket by simply pulling on thecable. Always remove

Software InstallationThe software installation refers to the installation of corresponding displaydrivers; the installation of the touch screen compri

Software InterfacesTouch ScreenTouch ScreenTouching the screen corresponds to press the left mouse key. The touchscreen programming interface is ident

Automated Logic Diagram (ALD) and PinAssignmentsfixed key legendfree key legend but fix effectof key7413150KYBDBEETLE-CPU PentiumCASHDRCOM4COM3COM2COM

InterfaceAutomated Logic DiagramThe LCD interface is connected to the TFT controller via a 50-pin cable.The inverter, LCD display, touch screen contro

ContentsIntroduction ... 1From Point-of-Sale to Point-of-S

Pin AssignmentsPin Assignments ControllerBA71/BA72 Connectors of the Controller and the InterfacePIN # signal PIN # signal1 P12VLCD 2 P12VLCD3RxD14TxD

COM 6 Interface of the ControllerPIN # signal1 +12V2RxD3TxD4DTR5 GND6DSR7RTS8CTS9+5VInternal Speaker Connector for Controller and BEETLE-CPUPIN # sign

Internal Connecting SocketPIN# COM7 COM81P5V P5V2 GND GND3 DCD DCD4 GND GND5CTS CTS6DTR DTR7RTS RTS8TxD TxD9DSR DSR10 RxD RxD11 RI RI12 GND GND13 P12V

External Connecting SocketPIN# with power supply w/o power supply1 +12V DCD2RxD RxD3TxD TxD4DTR DTR5 GND GND6DSR DSR7RTS RTS8CTS CTS9+5V RIController

Technical DataThe following operating conditions are valid for a BA71/BA72 TFT that isfitted with all the available modules (LCD flat screen, touch sc

LCD ScreenLCD ScreenTechnical D ataFrequenciesHorizontal (KHz) 29Vertical (Hz) 47SolutionsHorizontal 800 pixel (SVGA)Vertical 600 lines (SVGA)Colour R

BA71SNIkey TFTDimensionsScreen size 10.4" (26.4 cm)Active Screen(horizontal x vertical)211 mm x 158 mmCable length 1.8 mDimension Display Housing

BA72DimensionsScreen size 12.1" (30,7 cm)Active screen size(horizontal x vertical) 246 mm x 185 mmCable length 1.8 mDimension Display Housingwith

Current ConsumptionCurrent ConsumptionTFT Controller450 mA + 5V50 mA +12V50 mA -12VScreen ModuleConsisting of an LCD display, touch screen incl. contr

TFT ControllerTFT-ControllerInterfacePCI, 32 BitModeSVGAResolution800 x 600 x 256 colours, 64ksee chapter 2 TFT LCD flat screenImage repeat memory1 MB

Installing and Securing the Screen into Place ...23Installing the BA71 / BA72 into Place (Table Top Version)...

COM BoardCOM-Board ControllerSystem interfaceISA, 8 MHzI/O-addresses forCOM interfaces3 address records 2E0, 330, 320 thatcan be set by jumperInterrup

Manufacturer’s Declaration and ApprovalGeneral AuthorizationThis device fulfills the requirements of the EEC standard89/336/EEC “Electromagnetic Compa

Tested SafetyThe BA71/BA72 has been awardedthe GS symbol for “Geprüfte Sicher-heit” (tested safety). BA71/BA72 ful-fills the requirements for ergonomy

Safety InstructionsThis device conforms to the corresponding safety regulations for informati-on technology devices, including electronic office machi

Instructions for MaintenanceManufacturer’s Certificate and Notes Instructions for MaintenanceClean your BA71/BA72 TFT regularly with an appropriate su

The BA71/BA72 is manufactured without the use of CFCs and CCHS andis produced mainly from reusable components and materials. The proces-sed plastics c

AppendixAbbreviation IndexASCII American Standard Code for Information InterchangeAT Advanced TechnologyBIOS Basic Input Output SystemCFL Cold cathode

Technical Data ... 47Touch Screen (optional)...

IntroductionFrom Point-of-Sale to Point-of-Service“The customer is king”, a motto that seems so simple and yet it demandsa forever increasing supply o

The low-energy, flickerfree and radiation-free colour monitor of the BA71 /BA72 is an Active-Matrix-Display in TFT-technology (Thin Film Transistor).T